Power tools seen from above on a bench covered in sawdust

Van Conversion Tools: Drill, Rivet Nut Tool and Multi-Tool

As an Amazon Associate I earn from qualifying purchases. Some links on this page earn us a small commission, at no extra cost to you. Full disclosure.

This guide covers drilling holes, setting threaded inserts and making fitting cuts. Start with the next planned operation rather than buying tools for an undefined build.

Quick answer

Use a drill for drilling and screwdriving, and a rivet nut tool when the installation specifies compatible threaded inserts. An oscillating tool needs an accessory matched to the material and cut. None of these tool specifications establishes a furniture anchoring system.

All 3 picks at a glance

Astro 1442 rivet nut tool kit with mandrels and rivet nuts
For threaded inserts

Astro 1442 Rivet Nut Tool Kit

Astro lists rivet nut capacity up to M8 or 5/16 inch. Read more

Get yours on Amazon
DEWALT DCD771C2 compact drill driver kit with two batteries
For drilling and driving screws

DEWALT DCD771C2 Drill Driver Kit

Compact two-speed drill-driver kit with two batteries and a charger. Read more

Get yours on Amazon
DEWALT DCS356C1 oscillating multi-tool kit
Three-speed oscillating tool

DEWALT DCS356C1 Oscillating Tool Kit

DEWALT identifies DCS356C1 as a brushless three-speed kit with up to 20,000 no-load OPM. Read more

Get yours on Amazon

How we compared them

This comparison covers manufacturer descriptions, model specifications and installation requirements. The figures do not guarantee performance in a particular vehicle or boat.

What These Tools Cover

In short: Match the tool and accessory to the planned operation.
A person drilling into a wooden board on a workbench
A person drilling into a wooden board on a workbench. Photo: Matt Antonioli on Unsplash

Vehicle furniture anchors require a mounting plan specific to the vehicle and load. A tool's capacity does not approve an anchor location, fastener or furniture arrangement. Use the tool to carry out a specified operation rather than treating ownership of a rivet nut tool as a mounting design.

Match the cutting accessory to the material and type of cut. These three tools do not cover every drilling and cutting operation. Plan the holes, inserts and cuts first, then choose the compatible accessories and tool limits for those tasks.

Three tools, three operations

ToolOperationStated limit or kit detail
Astro 1442Operation: Threaded rivet nutsStated limit or kit detail: Up to M8 or 5/16 inch
DEWALT DCD771C2Operation: Drilling and screwdrivingStated limit or kit detail: Two-speed kit, two batteries, 1/2 inch chuck
DEWALT DCS356C1Operation: Oscillating-tool operationsStated limit or kit detail: Brushless, three speeds, up to 20,000 no-load OPM

Follow the product and installation guidance from Astro Tools, DEWALT drill and DEWALT multi-tool.

Astro 1442: Hand Tool for Threaded Inserts

In short: A manually operated option when the installation calls for compatible rivet nuts.
Astro 1442 rivet nut tool kit with mandrels and rivet nuts
For threaded inserts

Astro 1442 Rivet Nut Tool Kit

Get yours on Amazon

The Astro 1442 installs threaded rivet nuts up to M8 or 5/16 inch. Astro lists six mandrel sets and 60 rivet nuts in the kit. Match the mandrel and insert to the specified fastener rather than using the largest size because the tool can set it.

The tool has a manually operated double compound hinge handle. It installs the insert, but does not establish the strength of the surrounding vehicle panel or the finished mounting arrangement. Those requirements belong to the vehicle-specific mounting plan.

What could be better: M8 or 5/16 inch is the listed capacity ceiling. It is manually operated and does not turn a compatible insert into an approved furniture anchor by itself.

DEWALT DCD771C2: Drill and Battery Kit

In short: A drill-driver kit with two batteries and a charger.
DEWALT DCD771C2 compact drill driver kit with two batteries
For drilling and driving screws

DEWALT DCD771C2 Drill Driver Kit

Get yours on Amazon

The DCD771C2 has two speed ranges and a 1/2 inch chuck. The kit includes two batteries and a charger. DEWALT specifies 20V maximum initial battery voltage and 18V nominal voltage. Plan the required bits separately for the material and hole size.

Follow DEWALT's instructions for the material, accessory and operating limits. Chuck capacity alone does not establish suitability for a particular hole in steel or another material. Two batteries offer a way to use one while charging the other, rather than a guarantee of continuous work.

What could be better: The included batteries and charger do not make the kit complete for every drilling job. It still needs suitable bits, and its chuck size is not a guarantee of capacity for every material and hole.

DEWALT DCS356C1: Three-Speed Oscillating Tool

In short: Match the accessory to the planned cut.
DEWALT DCS356C1 oscillating multi-tool kit
Three-speed oscillating tool

DEWALT DCS356C1 Oscillating Tool Kit

Get yours on Amazon

DEWALT describes the DCS356C1 as a brushless three-speed oscillating tool kit with up to 20,000 no-load OPM. This is a no-load speed specification; choose the accessory for the material and cut.

Select the accessory for the material and the cut, and follow the model instructions. Do not assume an oscillating tool replaces every saw or that one included accessory covers all the panel work in a conversion.

What could be better: Its speed figure is a no-load specification, not a promised cutting speed. It needs a suitable accessory for each material and is not a universal replacement for every other cutting tool.

Which tool do you need next?

Start with the drill when the next job is drilling holes or driving screws. Add the rivet nut tool only where the mounting plan specifies compatible inserts. Select the oscillating tool and accessory for the particular cut rather than assuming it completes the toolkit.

Already own a drill? Compare its limits and available accessories with the planned work before buying another. Use the conversion guide to organise the wider job, while keeping the vehicle mounting design separate from tool selection. Next steps for your build: cargo van conversion for beginners and how to wire a camper van.

A cordless drill, an angle grinder and a hammer on a metal workbench
A cordless drill, an angle grinder and a hammer on a metal workbench. Photo: Sidney Pearce on Unsplash
Key takeaways
  • Confirm furniture mounting requirements using official guidance for the vehicle.
  • Astro lists a capacity of M8 or 5/16 inch for the 1442.
  • The DCD771C2 kit includes two batteries and a charger.
  • Match the cutting accessory and tool to the material and cut.

FAQ

What does a rivet nut do?

It provides an internal thread for a compatible bolt. Suitability for furniture depends on the complete mounting arrangement, surrounding material and load requirements.

Do I need two drill batteries?

Two batteries let you use one while charging the other. The DCD771C2 includes two batteries and a charger, but the work pattern still depends on the job and charging time.

Can an oscillating tool replace a saw?

It is not a universal saw replacement. Choose the tool and blade for the material and planned cut rather than treating its no-load speed as a cutting-performance comparison.

What drill size do I need for an M6 rivet nut?

Astro lists 9 mm for the M6 inserts in its 1442 kit. Use the specification for the exact insert and material, together with Astro's instructions, rather than treating thread size as the drill-hole diameter.

Affiliate disclosure. This post contains affiliate links. If you click and buy something, this site earns a small commission at no extra cost to you. Product details are based on manufacturer specifications and installation guidance. As an Amazon Associate I earn from qualifying purchases. Read the full affiliate disclosure. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.

Your next step

Cargo Van Conversion for Beginners: 5 StepsCargo Van Conversion for Beginners: 5 Steps How to Wire a Camper Van: Fuse Block, Cables and LightsHow to Wire a Camper Van: Fuse Block, Cables and Lights Van Sound Deadening: 3 Butyl Mats for a Quieter Van ComparedVan Sound Deadening: Three Butyl Mat Packs Compared

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *